Usually, the cold itself isn’t the whole problem. Colder weather means longer heating cycles and more demand on the system. Symptoms like
- A filter that’s getting clogged
- Flame sensor that’s getting dirty
- An ignition part that’s starting to fail
may go unnoticed during mild weather. If the furnace is running but you’re getting cold air from the vents, check what causes a furnace to blow cold air.
Why Cold Weather Makes Furnace Problems Worse
Your home loses heat faster when the outdoor temperature drops. To keep the inside temperature comfortable, the furnace has to run for longer periods.
That extra work can expose small problems.
For example, a slightly dirty filter may still allow enough airflow when the furnace only runs for ten or fifteen minutes at a time. But during a freezing week, the same furnace may be running much more often. Restricted airflow then becomes much harder for the system to deal with.
The same idea applies to other parts of the furnace.
- A sensor that has started getting dirty may work sometimes and fail at other times.
- An igniter may become unreliable.
- A vent that was clear yesterday may get blocked after snow or freezing rain.
This is why furnace problems often seem to appear on the coldest day of the year.
The Most Common Reasons a Furnace Won’t Start in Cold Weather
Below are the most common reasons for a furnace that doesn’t work.
A Clogged Air Filter
The filter is one of the first things you should check.
Take a look at the filter and check for a heavy buildup of dust and debris. If it’s dirty, replace or clean it according to the furnace and filter manufacturer’s instructions.
There’s no single replacement schedule that works for every home. Filter type, pets, dust levels and how often the furnace runs all make a difference. During the heating season, checking the filter regularly is a much better habit than waiting for a fixed date on the calendar.
Modern furnaces have safety controls that can shut the burners down when this happens. If your furnace keeps turning on and off before the house warms up, read why a furnace short cycles.
A Dirty or Failing Flame Sensor
Does the furnace light and then shut off a few seconds later? The flame sensor may be one of the reasons.
The flame sensor confirms that the burners have actually ignited. If the furnace can’t confirm a flame, it closes the gas valve as a safety measure. Over time, residue can build up on the sensor and interfere with that reading.
The furnace may then go through repeated ignition attempts or eventually lock itself out.
Cleaning or replacing a flame sensor involves the furnace’s ignition system. Take professional furnace services to address this issue.
A Frozen or Blocked Exhaust Vent
If you have a high efficiency furnace, you may notice one or two plastic pipes coming through an outside wall.
These are part of the furnace’s intake and exhaust system.
During heavy snow, freezing rain, or very cold weather, those openings can become blocked. When the furnace can’t move air or exhaust gases properly, its safety controls may stop the heating cycle.
If your furnace suddenly stops working after a storm, it’s worth taking a look outside.
Clear away loose snow, leaves, or other debris that you can safely reach. Don’t force tools inside the pipe or try to break heavy ice off in a way that could damage the vent.
If the opening keeps freezing or the furnace still won’t start after it’s clear, call a technician for heating services.
Pressure Switch or Inducer Motor Problems
A gas furnace goes through several steps before the burners light. One of those steps involves the inducer motor. It helps move combustion gases through the venting system.
The furnace also has a pressure switch that checks whether this airflow is working as it should.
If the furnace doesn’t get the right reading, it won’t continue with the normal startup process.
You may hear a small motor running or hear the furnace trying to start, but the burners never come on. The cause could be
- The pressure switch itself
- Inducer motor
- Blocked vent
- Drainage problem or something else in the system.
This is where guessing usually gets expensive.
A technician can test the parts properly and find out what’s actually stopping the furnace from starting.
Igniter Failure
Most newer gas furnaces don’t use the old-style standing pilot light. They use an electronic ignition system.
If the igniter is worn out, cracked, or no longer working properly, the burners won’t light. You may hear the furnace begin its normal startup routine but never hear the burners fire.
An igniter can fail with age, and the symptoms may look similar to other furnace problems. That’s why it’s better to have the system checked before replacing parts. A proper diagnosis can save you from paying for something you didn’t need.
What You Can Check Before Calling a Technician
Before booking a furnace repair, there are a few simple checks you can do yourself.
You don’t need tools for most of them.
- Filter: If it’s clearly dirty, replace it. Make sure the new filter is facing the right direction.
- Thermostat: Make sure it’s set to HEAT and the temperature setting is higher than the current room temperature. If the thermostat uses batteries, try replacing them if they’re old.
- Exhaust vents: If your furnace vents through an exterior wall, look for snow, ice, leaves, or anything else blocking the openings.
- Circuit breaker: Check the breaker for the furnace. A tripped breaker is an easy fix.
- Reset button: Some furnaces have a reset button on the burner housing. If the furnace has locked out, press it once. If it locks out again after firing briefly, do not keep resetting it. That is a signal to call for professional help.
When to Stop Troubleshooting and Call Heating Experts
There’s a point where basic checks should stop.
If you’ve checked the thermostat, filter, furnace switch, breaker, and outside vents and you still have no heat, the problem is probably inside the system.
The same applies if the furnace keeps starting and stopping, makes new noises, fails to ignite, or keeps showing a fault code. Repeatedly resetting the furnace isn’t a good solution.
Blue Sea Plumbing handles furnace repairs across North Vancouver, Ladner, Surrey, Maple Ridge, Pitt Meadows and White Rock. If your furnace is not starting and the house is getting cold, contact us or give us a call and we will get someone out as quickly as possible.
If you notice a burning smell when the furnace starts, don’t ignore it. Check the common reasons a furnace smells like burning.
How to Prevent Cold Weather Furnace Problems
A furnace can still break even when it has been maintained, but a little attention before winter can help catch problems earlier.
Start with the filter. Check it during the heating season and replace it when it’s dirty. Good airflow makes life much easier for the furnace.
A technician can check the ignition system, burners, safety controls, venting, and other parts that may be starting to wear out.
Pay attention to changes too. If the furnace suddenly takes longer to start, turns on and off more often, or starts making a noise you haven’t heard before, don’t wait until it stops completely.
You should also know where your outdoor furnace vents are. After heavy snow, you’ll be able to check them quickly instead of trying to find them while the temperature inside the house is already dropping.
And if your furnace has been short cycling for days or weeks, get it checked. A furnace that keeps starting and stopping is telling you something isn’t right.
FAQ
Why does my furnace work fine in fall but not in winter?
Your furnace has to work harder when the weather gets colder. Longer heating cycles can make an existing problem more noticeable. A dirty filter, flame sensor issue, ignition problem, or blocked vent may not cause obvious trouble during mild weather but can become a problem once the furnace is running much more often.
Why does my furnace start and then shut off after a few minutes?
This is called short cycling. The most common causes are a dirty air filter causing overheating, a dirty flame sensor giving a false reading, or a frozen exhaust vent triggering a safety shutdown. Check the filter and the exterior vents first.
Is it safe to keep resetting my furnace when it keeps shutting off?
No. If the furnace keeps going into lockout or shutting itself down, don’t keep resetting it. The furnace may be responding to a problem that needs to be checked. Repeated resets can also make it harder to see what caused the original fault.
Can cold weather damage a furnace permanently?
Cold weather by itself usually isn’t what damages the furnace. The bigger problem is running a system that already has a fault. Poor airflow, overheating, ignition problems, or worn parts can become more serious when the furnace is working hard every day.
How often should a furnace be serviced in Surrey?
Once a year, ideally in early fall before the heating season. Annual furnace servicing is a good habit, especially before or near the start of the heating season. It gives a technician a chance to catch problems before the furnace is under its heaviest winter workload.
Furnace Still Won’t Start?
If you’ve checked the simple things and you still don’t have heat, don’t spend the day guessing at parts or repeatedly resetting the furnace.
Get the problem diagnosed properly.
Blue Sea Plumbing & Heating provides furnace repair and heating service across Surrey and the Lower Mainland.
Get in touch with Blue Sea Plumbing & Heating to book a furnace inspection or repair.



